The whole automatic capping  machine adopts elaborate DIY design.By eliminating unnecessary complex and heavy machinery, it adopts suit type assembly.The maintenance and servicing can be completed without professionals.when it is necessary to replace the product,just make some simple adjustments, it can be immediately put online for production.

The machine is suitable for capping various types of round bottles in such industries as food, condiment,medicine,wine,oil and cosmetics etc.

Drawing for model YX-AC50 rings sealing machine :

Basic parameter of model YX-AC50 rotary sealing machine for glass jars:

Model YX-AC50
Speed: 20pcs-40pcs per min
Rated voltage: 　　110Ｖ/60Hz(USA market customized)
Machine Power: 　　800Ｗ
Exterior dimension: 　　About 2300*1800*1800 MM (L*W*H)
Air Pressure: 0.7-1.0 MPa
Weight: 　　About 400 Kg

Notification before Operation of the rotary sealing machinery

1: Before the machine is plugged in, make sure the power switch is in the closed state, and then follow the instruction.

2: If the machine does not run in a long time, it should be wiped with a piece of dry cloth and must not be cleaned with any corrosive cleaning agent.

3: It is strictly prohibited to spurt any liquid into the electric box of the machine, so as to avoid corrosion to the internal electrical components and cause short circuit.

4: Check according to the equipment packing list models, specifications and quantity of the equipment and materials to make sure that they meet the requirements of design and product standards and accompanied by certificates of conformity.

5 : Check the appearance of the equipment to make sure that it is free from any deformation, damage and corrosion, and all spindles that they should be flexibly rotating without any blockage.

6 : This machine is working under single phase AC 110V, and the flat 3-legged power plug should be plugged into the power socket with a ground wire.

How to operate the model YX-AC50 rings sealing machine glass bottles capper equipment:

Press the "Power Button" and the touch screen shows as follows:

It is the boot picture and also the picture to select an operation language:

Click "English" to enter the following picture:

The picture also has the following functions:

    1, Start up the equipment. When the equipment is in the normal standby mode, click  and then it shows

"AUTO" equipment is in a readiness state, then click, and the equipment will be in an operation state.

Note: if the equipment is still in the standby state, check the prompt below the screen, eliminate the alarm as required and then it will be normally started.

2, Output setting, output zero clearing. Click  to clear the current output and the equipment will be started counting from 0.

3, Empty the remaining materials on the turntable. After the completion of the products to be completed, if there are still remaining materials in the turntable, click  to clear bottles in the turntable.

Click to enter the following picture.

This column screen is for manual debugging

Only when shows “Man”, buttons in the picture are valid.

Click to enter the following picture:

This picture is used for setting of the process parameters.

Incoming bottles detection time: when bottles are induced in the bottle-mouth, delay the time before the cylinder moves to block later bottles.

Glanding time: when the caps are pressed on the bottle mouth, stay at the time and loosen up.

Cap locking time: when the cap locking motor is pressured on the bottle mouth, stay at the time and loosen the motor up.

Alarm and trouble-shooting method:

1、Emergency stop has been pressed. Push the emergency stops on the machine cap and next to the touch screen.

2、The output reaches the set value. Set the output, press the clear button to clear the current output.

3、When caps are not detected for a long period of time, please check. Check the bottle cap induction fiber as to whether it is well provided. Check whether caps are in place or not.

4、When bottles are not detected for a long period of time, please check. Check as to whether bottles are in place.

Electric eye adjusting:                                                                                      1.  Amplifier structure

Diagram for Optical fiber:

1.Optical fiber lock bar 2.Operating status indicator

3.Set  4. DSC indicator light

5.Digital monitor 6.Manual button

7.Extended protection cover 8.Expansion connector

9.Power Selector Switch 10. Mode button

11.Output selector 12.Cables

13.Dust protector 14.Set value (In green)

15.current value (In red)

Working process for the fiber optical setting:

Step one: When the electric eye falls in the gap, the red current value is 144.

Step two: When the electric eye falls on the label, the red current value is 4.

Step three: Adjust the set value",about 1/2 of the value that the electric eye is on the body paper (in the gap between the objects to be detected) and the value that the electric eye is on the paper
the set value is (144+4)/2=74, adjust the manual button to adjust the set value to be 74.

Step four: Move the label gap back and forth in the electric eye location and the red “signal light/indicator light”.

Circuit description:

触摸屏Touch screen

开关电源Switch Power Supply

变频器Frequency converter

刹车盘Brake disc

电源指示灯Power indicator light

转盘电机Turntable motor

调速器Governor

断路器Circuit breaker

Wooden case packing for rings sealing machine automatic model YX-AC50

ALL RIGHTS RESERVED by ®PENGLAI INDUSTRIAL CORPORATION LIMITED