SHENZHEN PENGLAI Industrial Corporation Limited
SINCE 2003
CERTIFICATES
CONTACT US

Email:jackdu999@yahoo.com

Tel:+8675586718316

Phone:+86-15811882441

electronics cables wiring flags folding labeling machine semi automatic with customized feeding positioning system sticker labeller customized equipment
electronics cables wiring flags folding labeling machine semi automatic with customized feeding positioning system sticker labeller customized equipment
Model YX-WL50B
Applicable label parameters: label roll diameter 1.5〞-2.0",
outside diameter MAX200mm; (other specifications need to be customized)
Label material: PVC, PET, cloth, paper, etc.
Label specifications L*W:25*10mm Minimum; Max: 100*50MM
Labeling accuracy: ± ≤ 0.5MM
Capacity: 800PCS-1000/H or more;
Dimensions(mm): 1126L*600W*1136H;
Machine weight: 70KG Package weight: 85KG
Applicable wire harness: wire outer diameter MAX4mm MIN3mm;
Description

This labeling wire cables machine is used for the folding and labeling of wiring cables,harnesses flags and round bars in the electronics industry.

Notice before using the wire labeling machine model YX-WL50B:

►Make sure the power supply voltage (AC220V) and the air pressure 4-6kgf before power on, and the external power supply must be grounded reliably.

►Do not block the chassis cooling holes.

►Non-professional technicians are strictly prohibited from opening the chassis.

►When the device is in operation, physical contact with the movement range is strictly prohibited.

►When the equipment fails, the power switch should be turned off first, and it is forbidden to carry out maintenance.

Technic Performance of model YX-WL50B labeling machine

Machine drawing dimension wire labeller.jpg

wire labeling machine model YX-WL50B.jpg

side shot on labelling.jpg

back side wire labeling machine semi automatic.jpg

Model YX-WL50B

Applicable label parameters: label roll diameter 1.5〞-2.0",

outside diameter MAX200mm; (other specifications need to be customized)

Label material: PVC, PET, cloth, paper, etc.

Label specifications L*W:25*10mm Minimum; Max: 100*50MM

Labeling accuracy: ± ≤ 0.5MM

Capacity: 800PCS-1000/H or more;

Dimensions(mm): 1126L*600W*1136H;

Machine weight: 70KG Package weight: 85KG

Applicable wire harness: wire outer diameter  MAX4mm  MIN3mm;

Labels final product wire labelled samples:

specification.jpg

labels samples.jpg

Wooden case package for DHL courier shipping of wire labeling machine model YX-WL50B:

machine in film wrappings.jpg

wooden case for wire labeling machine.jpg

wire labeling in truck for shipping.jpg

Detailed instruction of how to operate wire flat folding labeling machine as below:

installation

►Move the device to the desired installation location.

►Adjust the positioning screw at the bottom of the device to make it smooth.

►Item list for controlling panel of wire labeller model YX-WL50B

drawing of labeling machinery semi automatic.jpg

Operation method

Clip adjustment as shown (a total of three groups of six) Loosen the locking screw and place the wire harness to be machined into the V-shaped groove under the crimping block. After the wire harness is tightened, tighten the screw.

clipping adjustment.jpg

Label installation and commissioning

First install the label to the delivery wheel set as shown below

 Note: The label must be passed through the label eye, and the label should be straightened and straightened.

Lables adjustment.jpg

Labels adjustment 2.jpg

Align the position of the label with the triangular mark of the label's sensor eye, press and hold the button on the eye until the electric eye begins to blink, then align the position of the unlabeled eye with the eye, and press the button to extinguish the blinking light;

Adjust the vacuum template according to the wire diameter reference scale

 Parameter adjustment

Turn on the power switch, as shown below

Switch the device to manual mode

Out of standard position: The value is proportional to the standard position. Adjust the position of the outbound label to match the peeling plate and transfer the label to the following position.

Stripping board.jpg

Speed setting

parameter of labeling wire machine smei automatic (8).png

Click on the speed settings to enter the speed settings page as shown below, according to the operating habits can be set.

If the accuracy is higher, please reduce the speed of the motor.

Positioning settings

Click on the positioning settings to enter the positioning settings page as shown below

parameter of labeling wire machine smei automatic (6).jpg

Fitting motor parameters in detail

Fit the first move angle: the first move angle of the target before it is pasted

Binding contract dynamic angle: the angle of synchronization of the target plate at the time of affixing and entering the line, this value will affect the tightness of the label and the wire.

Fit end point angle: The position of the target plate is fully fit in place, the value of the small label does not match, and the motor will overshoot if the value is too large.

Into the line motor parameters in detail:

The position of the contact surface of the clip and the label: the position of the contact between the wire and the label, the value of the small wire and the label cannot be contacted, and the label is not well-labeled; the large value line will press the label down and the label is not well-labeled; the proper position should be the wire The label just came into contact with as well

Sticking into the line angle: the position of the target when the target moves synchronously with the wire, the value of the small label is not tight; the value label will pull too tightly or pull the label

Tag tightening angle: When the target plate and wire synchronous action is completed, further tightening is performed; the value of the small label is not tightly attached; the value label is pulled too tightly or the label is pulled

Rotary motor parameters in detail:

Label left and right positions: When the label is left-shifted, the value is increased; when it is right-shifted, the value is decreased.

Rotation end point angle: The position of the target plate rotating out of the line clamp is to be a right angle; when the left side is smaller, the value is smaller; when the right side is right, the value is increased.

wiring harness.jpg

The wire diameter parameter changes with the wire diameter. The corresponding parameters in the wire are described as follows

Crimping and label contact surface position: Adjust the labeling parameters in manual mode so that the label and wire harness make contact as follows

The corresponding parameters of the tuning parameter settings are as follows

Rotary motor and inlet motor speed ratio: Correct the fit of the two motors, collision avoidance machine.

Fit motor parameters: Adjust the fit of the label to correct the error;

Rotating motor parameters: adjusting the rotary angle correction error of the vacuum chuck;

Centering adjustment (as shown below)

center adjustment.jpg

Loosen the locking screw, adjust the alignment lever so that the label is in the middle of the harness, and then tighten the screw.

Maintenance and Maintenance

Heavy pressure is strictly forbidden. Please keep it clean;

 Lubricate the machine on schedule

 One month plus one lubricant for the target's location

  Three months inspection of the timing belt wear of various parts of the machine

ALL RIGHTS RESERVED by ®PENGLAI INDUSTRIAL CORPORATION LIMITED

Reviewed Products
  • Labeling machine customized labeler semi automatic flag labels applicator for dog bone Pet food packaging
  • Syringes filling machine vertical type gel PSF syrine filler equipment Semi automatic multifunctional machinery
  • Pattern filling machine multiple colors cosmetic cream bottles filler equipment for bottling helix pearl flower type product
  • Bottles unscrambler equipment automatic big &small round plastic bottle unscrambling sorter machine with PLC touch screen controller
  • Pneumatic type tall thick cans seaming machine semi automatic metal tin sealer equipment