The continuous band seraler is ideal for heat sealing of laminated or non laminate pre-made pouches.

Application of the machine

This machine is used for sealing various pre-made pouches and it is a best sealing equipment to be widely used in food & groceries, seed processing units, pharmaceuticals, chemical industries, dairy, cosmetic, automobile spare parts, electronic spare and online and offline packaging of respective product range.
Working principle for plastic bags sealing machine:

(1) Guide, (2) Driven Wheel Seat (Adjusting Block), (3) Driven Wheel, (4) Control Panel, (5) Heating Block, (6) Holding Plate, (7) Pinch Roller,
g Roller, (11) Silicone Wheel, (12) Guiding Wheel, (13) Conveyor Belt, (14) Conveyor Table, (15) Fastening Knob for Elevating
Table, (16) Transverse Tightening Knob for Conveyor Table, (17) Conveyor Support


a band sealer for continuous sealing cycle, a conveyor will move the material to seal between the heating jaws, mostly irons containing a heating cartridge. This element is always heating to allow a continuous scrolling of material.

Once the heating irons passed, the material passes between cooling irons effectively ventilated to allow heat to dissipate and material to congeal. Then follows the passage of knurling, the material passes between two knurled wheel that will give their final appearance to the seal.

Finally, the conveyor leads the material on other accessories(date coder, trimmer...), on a packaging line, or just let the material finish his race in a carton

Basic parameter of model YX-H1000 band sealing equipment:

Model YX-H1000 Horizontal plastic bags sealing machine

Operation: Electronic variable speed
Temperature control: electronic thermostat control
Printing method: Stamps
Power: 220V/50Hz 500W
Seal products speed :0-12m / min
Seal products Thickness :0.02-0 .80 mm
Seal width :6-10mm
Sealing length: 0 - infinity
Transporting loads: <5kg
Temperature range :0-300 °C
Dimensions: 840 × 380 × 320mm
Weight: 32kg(refered on horizontal model)

Features of band sealer semi automatic tabletop sealing equipment:

Your band sealer is equipped with a wide range of standard features and capabilities.
►Simple to use – minimal operator training
►Rust inhibiting stainless steel construction
►Equipped with bag entry guide for easy bag feeding and straight seals
►Unit feeds left to right (see CBS-880 for right to left feeding)
►Control panel includes industrial grade safety emergency stop switch
►10amp protection power surge breaker
►Includes pressure embossing coder
►Wide seal (8mm) to assure airtight seal / Optional 15mm width sealer model available
►PTFE sealing belts
►Extended forced-air cooling system with extra wide cooling bars and 6 heat transfer orifices
►One pair of brass sealing bars
►Sealing method – constant heat
►Adjustable 2-way pulley system for optimal stability and embossing clarity
►Knurled pressure rolls with variable pressure adjustment
►Fast warm up time
►PID digital temperature controller 0-300˚C (572˚F) with dual alphanumeric displays (target & current temp)
►Motorized rubber conveyor with speed control
►Capable of speeds up to 472 inches/minut

OperationSet-up

1. Our machines are equipped with a three-prong ground plug.Make sure the plug is well-connected with socket to ensure safe operation.
2. Make sure the circuit breaker is in the “ON” position.(Levers pointing up)
3. First time operation. Allow the machine to pre-heat by running at the low temperature for a few minutes.
This would apply if the machine has not been in operation for a long time. The machine can sometimes be damp from storage or shipment and running at a low temperature will dry out any

residual moisture.
4. For some materials, an adjustment to the clearance between the upper heating block and bottom heating block and upper cooling block and bottom cooling block may be necessary. Adjust the clearance between by
turning the stopping flake clockwise (increase distance) to raise the block our counterclockwise to lower the block (decrease distance). The clearance should be equal to the thickness of one layer of your material to be
packaged. This will ensure high seal quality and embossing.Please note that the majority of materials sealed will NOT need adjustments.

Figure 8. (1) Screw, (2) Stopping Flake, (3) Fastening Screw, (4) Nut .

How to install embossing letters for the band sealing machine:

Spare Parts List
Included with your band sealer are the following parts. Please note that spare parts included with your band sealer
are subject to change without notice.
►Typeset Box which includes numbers (0-9), Letters - EXD, embossing wheel, and key wrench
►Power Cord
►PTFE Sealing Belts
►Drive Belts
►Speed Adjusting PC Board

ALL RIGHTS RESERVED by ^®PENGLAI INDUSTRIAL CORPORATION LIMITED